GCC 표준 지도

The standard outlines the specification and requirements for Unleaded Gasoline (91 RON, 95 RON, and 98 RON) intended for use in engines designed to op…

The standard outline the specification and requirements for Diesel Fuel (Gasoil) intended for used in diesel engine designed to operate on automotive …

This draft GSO standard specifies the minimum requirements, sampling and test method for Automatic Transmission Fluids (ATF) based on road vehicles su…

- Standard specifies the Characteristics and requirements for one grade of kerosine type aviation turbine fuel intended for use in aircraft gas turbin…

The GSO standard is concerned with lubricating oils for internal combustion engines suitable for gasoline and diesel engine services (excluding marine…

This standard covers butane liquefied petroleum gas. This standard is intended to properly define acceptable specifications for butane use in domestic…

The GSO standard is concerned with Motorcycle Four-Stroke Cycle Gasoline Engine Oils commonly used for the lubrication of engine, clutch and transmiss…

This standard covers the characteristics and property of base oils, used as lubrication grade oils that initially produced from: a) Refining of crude …

이 걸프 표준은 분사 냉각 시스템이 장착되지 않은 윤활 압축실을 갖춘 공기 압축기에 사용되는 윤활유에 적용한다. 이러한 윤활유는 대기압보다 높은 압력으로 공급하도록 설계된 진공 펌프에도 사용할 수 있다.

이 걸프 문서는 가솔린 및 경형 디젤 엔진, 후처리 장치가 있는 엔진, 그리고 ACEA 성능 분류에 따른 중형 디젤 엔진(선박용 제외)에 적합한 내연기관용 윤활유를 다룬다.

This Gulf standard is concerned with water-soluble cutting oil that can be used as a coolant/ lubricant for general purpose machining of metal such as…

This GSO material specification covers welded and seamless carbon steel pipes (including low temperature Ni-containing grades listed in ASTM A333 and …

1.1 This specification is applicable to wrought stainless steel and nickel alloy pipe fittings manufactured in accordance with ASME B16.9 and the mate…

This standard is concerned with the standard methods that apply to procedures for obtaining representative samples of asphalt materials whether in liq…

This test method covers the ability of turbine, hydraulic, and gear oils to separate entrained air. NOTE (1): This test method was developed for hydro…

1.1 This Gulf standard is concerned with the determination of basic constituents in petroleum products by titration with perchloric acid in glacial ac…

This Gulf Standard is concerned with asphalt binder graded by Penetration for use in the construction of pavements. NOTE (1): For asphalt binders grad…

1.1 This Gulf Standard concerned with the procedure for determin¬ing the ductility of an asphalt material measured by the distance to which it will el…

1.1 This Gulf standard specifics HLP hydraulic oils that are recommended for use in hydrostatic fluid power systems, where high thermal stresses are l…

1.1 This Gulf standard specifics HVLP hydraulic oils that are recommended for use in hydrostatic fluid power systems, where high thermal stresses are …

1.1 This Gulf standard is concerned with the requirements to be met in CLP Lubricating oils. 1.2 CLP lubricating oils are generally used in circular a…

1.1 This Gulf standard is concerned with the requirements to be met in CL Lubricating oils. 1.2 CL lubricating oils are used in circular and splash lu…

This Specification defines the requirements for material selection, connections, detailing, fabrication, galvanizing, painting and coatings, marking f…

This Specification only applies to high frequency welded (HFW) pipe, outside diameter 114.3 mm (NPS 4) and larger, for use in Class B and Class C. Pip…

1.1 This standard prescribes mandatory requirements for installation and application of DC power systems (stationary storage batteries and battery cha…

1.1 This GSO Material Specification defines the minimum mandatory requirements for fail-safe, fault-tolerant, programmable controller based Emergency …

1.1 This specification defines the minimum mandatory design, fabrication and testing requirements for a Distributed Control Systems (DCS). 1.2 This sp…

1.1 This specification defines the requirements for instrument control panels, control cabinets, and marshalling cabinets for location in electrically…

1.1 This specification defines the requirements for instrument control panels, control cabinets, and marshalling cabinets for location in electrically…