GCC 표준 지도

1.1 This Standard covers construction and performance requirements for the tank accessories identified in Clause 1.2, for use on atmospheric abovegrou…

This part of IEC 62933, which is a technical report, focuses on the necessity of using repurpose and reuse batteries in BESS. This document also illus…

1.1 This specification covers carbon-steel wire and welded wire reinforcement produced from hot-rolled rod to be used for the reinforcement of concret…

1.1 This specification covers material in mat (or sheet) form fabricated from deformed steel bars to be used for the reinforcement of concrete. Mats a…

1.1 This specification covers high-strength low-alloy structural steel shapes, plates, and bars for welded, riveted, or bolted construction intended p…

1.1 This specification22 covers two grades (C and D) of carbon steel plates of structural quality for general application. 1.2 When the steel is to be…

1. Scope Clause 1.2: Revise Unless specified for use for other applications in Annex A2, bars are of four minimum yield strength levels: namely, 280 M…

1.2 Grade- Bars are of three minimum yield strength levels: namely, 420 MPa [60 psi], 550 MPa [80 000 psi], and 690 MPa [100 000 psi], designated as G…

1.1 This specification covers steel sheet metallic coated by the hot-dip process and coil-coated with organic films for exterior exposed building prod…

1.1 This specification covers vapor retarders for thermal insulation, specifically, flexible materials with permeance of 0.15 perm (8.63 ng·Pa-1 · s-1…

1.1 This practice covers procedures for preparing test panels of dry-mix or wet-mix shotcrete and for testing specimens sawed or cored from the panels…

1.1 This specification covers either untextured or surface textured fiber-cement flat sheets intended for exterior applications such as wall claddings…

1.1 This specification covers fiber-reinforced gypsum panels described in 1.1.1 - 1.1.6. 1.1.1 Interior Fiber-Reinforced Gypsum Panels are designed to…

1.1 This specification covers discrete fiber-cement sheets manufactured to be dimensionally stable and suitable for decoration as paint, wallpaper, na…

1.1 This specification covers non-asbestos fiber-mat reinforced cementitious backer units manufactured to be dimensionally stable and suitable as eith…

1.1 This test method covers a technique for determination of the emittance of opaque and highly thermally conductive materials using a portable differ…

1.1 This specification covers the gypsum boards described in 1.1.1 - 1.1.9. NOTE 1-Specifications C840, C841, C844 and C1280 contain application proce…

1.1 This specification covers extruded preformed flexible cellular polyolefin thermal insulation operating temperatures from-150°F to 200°F (-101°C to…

1.1 This specification covers the requirements for segmental concrete paving slabs manufactured for construction of pedestrian and roof applications f…

1.1 This specification covers returned fresh concrete for use in a new batch of ready-mixed concrete. Requirements for returned fresh concrete shall b…

1.1 This specification covers the qualification of materials for use as anti-washout admixtures to be added to hydraulic-cement concrete mixtures for …

1.1 This test method covers the determination of the amount of linear shrinkage and other changes that occur when a preformed thermal insulating mater…

1.1 These test methods cover the chemical analysis of gypsum and gypsum panel products, including gypsum ready-mixed plaster, gypsum wood-fibered plas…

1.1 This specification covers calcined gypsum mixed at the mill with other ingredients to control working quality and setting time; specifically desig…

1.1 This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry pan…

1.1 This specification covers brick intended for use as paving material subjected to pedestrian and light vehicular traffic. The units are designed fo…

1.1 This test method covers the determination of the acidity in aviation turbine fuel in the range from 0.000 mg⁄g to 0.100 mg⁄g KOH. 1.2 The values s…

1.1 This performance specification covers men’s and wom en’s sliver knitted overcoat and jacket fabrics composed of any textile fiber or mixture of te…

1.1 This performance specification covers men’s and boys’ woven dress suit fabrics and woven sportswear jacket, slack, and trouser fabrics composed of…