GCC 표준 지도

1.1 This standard defines the terms used in standards that are the responsibility of Committee D03 on Gaseous Fuels. These terms are used in: 1.1.1 Th…

1.1 This practice2 covers the types of and preparation of containers found most suitable for the handling of aviation fuel samples for the determinati…

1.1 This test method covers and applies to the determination of the “rest” electrical conductivity of aviation fuels and other similar low-conductivit…

1.1 These test methods cover the determination of the liquid limit, plastic limit, and the plasticity index of soils as defined in Section 3 on Termin…

1.1 This performance specification covers requirements for fillings for industry products such as wearing apparel, sleeping bags, and comforters conta…

1.1 This practice presents a procedure for calculating the unit weights and water contents of soils containing oversize particles when the data are kn…

1.1 This test method covers the determination of sediment in crude oils and fuel oils by extraction with toluene. The precision applies to a range of …

1.1 This guide describes how static electricity may be generated in petroleum fuel systems, the types of equipment conducive to charge generation, and…

1.1 This dynamic test method covers the procedure for applying an axial impact force with a pile driving hammer or a large drop weight that will cause…

1.1 This test method covers the quantitative determination of barium, boron, calcium, copper, magnesium, molybdenum, phosphorus, sulfur, and zinc in u…

1.1 These test methods cover the determination of the total lead content of a gasoline within the following concentration ranges: 0.010 g Pb ⁄US gal t…

1.1 This test method covers the sieve analysis of mineral fillers used in asphalt paving mixtures. 1.2 The values stated in either SI units or inch-po…

1.1 This test method is commonly referred to as the L-60-1 test.2 It covers the oil-thickening, insolubles-formation, and deposit-formation characteri…

1.1 This guide recommends standards for the characterization of fly ash from the combustion of coal, fly ash from coal combusted in the presence of a…

1.1 This test method covers the determination of nitrogen in liquid hydrocarbons, including petroleum process streams and lubricating oils in the conc…

1.1 This test method covers the description of the determination of the cloud point of petroleum products and biodiesel fuels that are transparent in…

1.1 This test method covers the description of the determination of the cloud point of petroleum products and biodiesel fuels that are transparent in…

1.1 This test method covers the determination of the cloud point of petroleum products and biodiesel fuels that are transparent in layers 40 mm in thi…

1.1 This test method covers four procedures for determining the evaporation loss of lubricating oils (particularly engine oils). The evaporation measu…

1.1 This test method covers the determination of the percentage, by mass or by count, of a coarse aggregate sample that consists of fractured particle…

1.1 This practice covers procedures and equipment for obtaining, mixing, and handling representative samples of volatile fuels for the purpose of test…

1.1 This test method covers the procedure for determining the integrity of individual vertical or inclined piles by measuring and analyzing the veloc…

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase a…

1.1 This guide covers the general procedures necessary to conduct caliper logging of boreholes, wells, access tubes, caissons, or shafts (hereafter re…

1.1 This test method covers the determination of the mass of particulate contamination in a middle distillate fuel by filtration. This test method is…

1.1 This test method covers the direct determination of entrained water in petroleum products and hydrocarbons using automated instrumentation. This t…

1.1 This test method evaluates the relative flammability of textiles and garments intended for use in children’s sleepwear. The procedures of this tes…

1.1 This test method covers procedures for checking the homogeneity and integrity of concrete in deep foundation such as bored piles, drilled shafts, …

1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantit…

1.1 This test method covers a test procedure for evaluating the rust and corrosion inhibiting properties of a gear lubricant while subjected to water …